390_22002_2
Topthema: Sound im Audi
Audio System RFIT Audi A6 C8 Evo2 – 20er System für Audi A6
Von Audio System gibt es eine Vielzahl an Nachrüstlautsprechern für Audi. Wir schaffen den Überblick und testen das RFIT Set für den A6 C8.
>> Mehr erfahren>> Alle anzeigen
462_22882_2
Topthema: Feurig
High-End-Standbox mit ESS AMT
Mit diesen Chassis wollte ich schon immer mal etwas bauen. Dass ich sie allerdings jemals zusammen in einer Box haben würde, hätte ich dann doch wieder nicht erwartet – dass das Ganze so gut werden würde, dann schon eher.
>> Mehr erfahren>> Alle anzeigenKategorie: Profi- / Musiker-Equipment
Ausstattungsliste: Quested Monitoring Systems SB10R
Ausstattung & technische Daten
| TECHNICAL SPECIFICATION | |
| Dimensions | Cabinet 600(w) x 332 (h) x 300(d) mm |
| SBC250 Controller – 1U case 270mm deep | |
| Weight | Cabinet – 19.8 kg / 43.4 lb |
| SBC250 Controller – 5.5 kg / 12 lb | |
| Drivers | Bass cone 1 x 250mm (10”) |
| Maximum SPL | 116 dB continuous pink noise @ 1m Leq 1 minute half space |
| Frequency Response | User Adjustable. 25 Hz-200 Hz ± 2 dB / 17 Hz-200 Hz -6 dB |
| Connector | 2 off XLR and ¼ inch jack combo socket |
| Impedance | 10k W electronically balanced with RF filters |
| Wiring | Pin 1 ground Sleeve |
| Pin 2 hot Tip | |
| Pin 3 cold Ring | |
| Outputs | Left and Right Monitor 2 off XLR type male left & right outputs |
| Impedance | 100 ohm electronically balanced |
| Sub Bass Output | 1 pair binding posts |
| Filters | Left & Right Input Summed to Sub Output |
| Subsonic/High Pass | -3dB @ 14Hz, 24dB/oct or -3dB @ 28Hz, 24dB/oct (set by internal jumper) |
| Low Pass | -3dB @ 40Hz to 135Hz, externally adjustable @ 24db/oct or full range on CH A Left & Right Input to Left & Right Output |
| Ultrasonic | -1dB @ 100k |
| High Pass | -3dB @ 40Hz to 135Hz, externally adjustable @ 24db/oct or full range on CH A |
| POWER AMPLIFIER | |
| THD | 210W rms continuous |
| 0.03% at levels up to 1dB below clip, 20Hz – 120Hz typ | |
| 0.005% @ 20W rms 100Hz | |
| Hum & Noise | -100 dB referred to clip |
| Power Requirements | Set by internal plug: normal 115V or 230V setting: Min 160V (restricted output power): Max 255V 115V setting: Min 80V (restricted output power): Max 127V |
| CONSUMPTION | |
| Quiescent | <30Wv |
| Typical use | 50W |
| Max | <200W |
| Note | 0 dBu = 775 mV into open circuit |
| CONTROLS | |
| Controls | Crossover Frequency 40 – 135Hz, front panel pot |
| Test (Band limited pink noise), front panel recessed switch (LED indicates when on) | |
| Sub bass bypass, front panel switch (LED indicates when bypassed) | |
| Sub Gain –14 to +6, front panel pot (Sub level indicated with LED Meter) | |
| Sub Phase, front panel pot | |
| Sub Polarity, front panel recessed switch (LED indication for positive and negative polarity) | |
| Power, front panel switch | |
| Left channel sub filter bypass, rear mounted recessed Switch | |
| Subsonic filter 14 or 28Hz, Internal jumpers | |
