390_22002_2
Topthema: Sound im Audi
Audio System RFIT Audi A6 C8 Evo2 – 20er System für Audi A6
Von Audio System gibt es eine Vielzahl an Nachrüstlautsprechern für Audi. Wir schaffen den Überblick und testen das RFIT Set für den A6 C8.
>> Mehr erfahren>> Alle anzeigen
462_22882_2
Topthema: Feurig
High-End-Standbox mit ESS AMT
Mit diesen Chassis wollte ich schon immer mal etwas bauen. Dass ich sie allerdings jemals zusammen in einer Box haben würde, hätte ich dann doch wieder nicht erwartet – dass das Ganze so gut werden würde, dann schon eher.
>> Mehr erfahren>> Alle anzeigenKategorie: Profi- / Musiker-Equipment
Ausstattungsliste: Quested Monitoring Systems V3110
Ausstattung & technische Daten
| TECHNICAL SPECIFICATION | |
| Dimensions | 380 x 600 x 360mm (w x h x d) |
| Weight | 39kg / 86lb |
| Drivers | Low Frequency 1 x 250mm(10″) |
| Mid | 1 x 75mm (3”) soft dome |
| High Frequency | soft dome 1 x 28mm (1 1/8″) |
| Maximum SPL | 115.5 dB continuous pink noise @ 1m Leq 1 minute. 121.5 dB continuous pink noise per pair @ 1m Leq 1 minute |
| Frequency Response | 34Hz – 20kHz ±2dB / 30Hz – 22kHz -6 dB |
| INPUT | |
| Connector | XLR3 type-Female |
| Impedance | 10k Electronically balanced with RF filters |
| Wiring | Pin 1 ground, Pin 2 hot, Pin 3 cold |
| Sensitivity | Rear mounted 10 position rotary switch calibrated in 2dB steps |
| Minimum sensitivity | +4dBu for 100dB SPL @ 1m |
| Maximum sensitivity | -14dBu for 100 dB SPL @ 1m |
| FILTERS | |
| Subsonic | -3dB @ 14Hz, 24dB/oct |
| Crossover Point | 650Hz, 2k5H, 24dB/oct. |
| User LF EQ | 4 position rear mounted selector to select FLAT for normal use. -9dB and -3dB for cut below 100Hz, +1dB for lift above 80Hz. |
| User MF EQ | 3 position rear mounted switch to select FLAT for normal use, CUT/LIFT +/-1dB for 650Hz to 2k5Hz. |
| User HF EQ | 3 position rear mounted switch to select FLAT for normal use, CUT/LIFT +/-1dB for 2k5Hz to 40kHz. |
| POWER AMPLIFIER | |
| LF output power | > 700W rms continuous (Note 1) |
| Mid Output | > 150W rms continuous (Note 1) |
| HF output power | > 150W rms continuous (Note 1) |
| THD | < 0.03% at levels up to 1dB below clip, 20Hz – 20kHz. typ 0.005% @ 20W rms 1kHz. |
| Hum & Noise | > -100dB referred to clip |
| Note | The continuous rating is for a period not exceeding 5 minutes with unrestricted airflow (100mm clearance) around the amplifier rear panel and ambient temperatures is <30 o C |
| INDICATION | |
| Power on | Front mounted LED (flashing blue) indicates power applied and warm-up cycle. |
| Optimum Performance | Front mounted LED lights constant blue. |
| Overload | Front mounted LED flashes red 0.5dB below signal clip. |
| Thermal Protection | Front mounted LED turns red, signal is muted and amplifier switches to standby mode during thermal protection cooling cycle. Normal operation resumes when amplifier temperature drops by 20 o C. |
| POWER REQUIREMENTS | |
| Voltage | Set by internal plugs: nominal 115V or 230V @ 50-60Hz AC. |
| 230V setting | Min 160V (restricted output power): Max 263V |
| 115V setting | Min 80V (restricted output power): Max 132V |
| CONSUMPTION | |
| Quiescent | 72W, typical use 110W. |
| Note | 0dBu = 775mV into open circuit. |
