Es gibt Lautsprecher und dann gibt es noch die LS3/5A. Sie spaltet sowohl ihre Hörer, als auch die, die sie gar nicht kennen. Warum das so ist? Nun, dafür muss man sich vor allem anschauen und natürlich hören, was sie kann und nicht, was sie nicht kann.
>> Mehr erfahren>> Alle anzeigenMit diesen Chassis wollte ich schon immer mal etwas bauen. Dass ich sie allerdings jemals zusammen in einer Box haben würde, hätte ich dann doch wieder nicht erwartet – dass das Ganze so gut werden würde, dann schon eher.
>> Mehr erfahren>> Alle anzeigenKategorie: Profi- / Musiker-Equipment
Ausstattungsliste: Manley JUMBO SHRIMP
Specification | |
Type | PREAMPLIFIER WITH REMOTE CONTROL |
ALL-TUBE | Vacuum Tube all-triode design |
Input Tubes | 2 x 12AT7EH large plate Electro-Harmonix Russian |
Interstage Follower Tubes | 2 x 5670 GE USA dual triodes |
Output Tubes | 2 x 7044 or 5687 GE JAN NOS |
Five Line Level Inputs | unbalanced RCA |
MUTE switch and Warm-Up muting delay | yes |
ALPS motorised volume control | Accurate tracking usually within 0.5dB. Smooth operation. (no detents) |
ALPS balance control | Center detented |
Record Output | (AKA "REC OUT") Unbalanced RCA jacks, unbuffered, passive (always ON) |
Main Outputs | Two sets of unbalanced RCA main outs for bi-amping or driving a powered subwoofer |
Gain | 12dB |
Input Impedance | 250 kOhm |
Input Sensitivity | Volume Control at MAX: 200mV in yields 0.8V out (12dB GAIN) |
Volume Control at 3 o clock: 200mV in yields 0.380V out (5.6dB GAIN) | |
Volume Control at 12 o clock: 200mV in yields 0.115V out (-4.8dB GAIN) | |
Maximum Input Level | 5V in produces 1.5% THD at output |
Frequency Response | 10 Hz - 80 KHz; 20 Hz - 20KHz, -0.3dB |
Noise Floor | Typically -83 dB 20-20K with volume control fully open |
Typically -95 dB A WGT 20-20K with volume control fully open | |
Noise Floor (shorted input) | Typically -94 dB 20-20K with volume control fully closed |
Typically -106 dB A WGT 20-20K with volume control fully closed | |
S/N Ratio | typically 95 dB A WGT 20-20K |
THD | 0.02% at 1V rms output |
Output Impedance | 50 Ohms |
Maximum Output | +23dBu @ 1.5% THD into 100K load (10.9V rms) |
+20dBm @ 1.5% THD into 600 Ohm load | |
Badge Lamp | LED illumination |
RF Remote Control | commands volume control UP/DOWN; uses 9V battery |
Power Consumption | 55 Watts (485mA @ 120VAC) |
Operating Mains Voltage | Units are purpose built for original destination countrys mains voltage: 100V, 120V, or 220-240VAC as indicated on the serial number badge. Power transformer must be replaced in order to change mains operating voltage. |
120VAC units may NOT be rewired to put the primaries of the power transformer in series for 220-240V operation or a large radiated field of hum will develop. If changing locations/voltages, the power transformer must be replaced with the dedicated one for | |
Dimensions | W=19", L=11", H=3 1/2" |