462_22882_2
Topthema: Feurig
High-End-Standbox mit ESS AMT
Mit diesen Chassis wollte ich schon immer mal etwas bauen. Dass ich sie allerdings jemals zusammen in einer Box haben würde, hätte ich dann doch wieder nicht erwartet – dass das Ganze so gut werden würde, dann schon eher.
>> Mehr erfahren>> Alle anzeigen
390_22002_2
Topthema: Sound im Audi
Audio System RFIT Audi A6 C8 Evo2 – 20er System für Audi A6
Von Audio System gibt es eine Vielzahl an Nachrüstlautsprechern für Audi. Wir schaffen den Überblick und testen das RFIT Set für den A6 C8.
>> Mehr erfahren>> Alle anzeigenKategorie: Profi- / Musiker-Equipment
Ausstattungsliste: Manley SNAPPER
Ausstattung & technische Daten
| Specification | |
| Type | MONOBLOCK POWER AMPLIFIER |
| Input Impedance | RCA: 475 Kohm |
| XLR: 15 Kohm or 600 Ohm switchable | |
| Input Sensitivity | RCA: 750mV input = 110W output |
| XLR @ 15Kohms: 1.5 V input = 110W output | |
| XLR @ 600 Ohms: 2.4 V input = 110W output (w/600 Ohm source) | |
| Gain | RCA: factory set for 31 dB; Range = 29.5 to 34.5dB |
| XLR: factory set for 25 dB | |
| Negative Feedback | factory set for 9dB of global NFB |
| Maximum Output Power | into 5 Ohms: 110 Watts (1.5% THD @ 1kHz) |
| into 8 Ohms: 100 Watts (1.5% THD @ 1kHz) | |
| Signal to Noise Ratio | Ref. 1W: Typically 90 dB A-WGT 20-20K |
| Noise Floor | Typically 105μV = -77dBu A-WGT |
| Typically 388μV = -66dBu unweighted | |
| Dynamic Range | 98dB |
| THD+noise @ 1W | less than 0.1% |
| Frequency Response | at 110W full power: 15 Hz to 40 kHz FLAT |
| at 5W into 5 Ohms: 10 Hz to 65 kHz FLAT, -3dB @ 100KHz | |
| Recommended Speaker Load | Optimized for 5 Ohms |
| Actual Output Impedance | 1.5 Ohms |
| Power Consumption | Idle: 170 Watts (1.4A @120VAC) |
| at Full Power 110W: 336 Watts (2.8A @120VAC) | |
| Operating Mains Voltage | Factory set for 100V, 120V or 220-240VAC operation for original destination countrys mains voltage. |
| Changeable with power transformer re-wiring and fuse value change. | |
| Mains Voltage Frequency | 50~ 60Hz |
| Tube Complement (per pair of Snappers) | Input Vacuum Tube: 2 x Ruby 12AX7 (matched pair) |
| Driver Vacuum Tube: 2x 5687 or 7044 (equivalent) (matched pair) | |
| Output Vacuum Tubes: 8 x Tungsol EL34B (matched) | |
| B+ Voltage | 570V DC |
| Output Tube Quiescent Standing Current | 30mA |
| Set Bias for | 300mVDC measured across 10 Ohm cathode resistor |
| Lamp type | "FuseLamp" size 1/4" X 1 1/4", 12 volt, 0.15 amp; Units built after 5/2003 use white LEDs |
| Fuse values & types for | 120VAC operation: MDL or MDA 4 AMP / 250 Volt SLO-BLO size 1/4" X 1 1/4" |
| 240VAC operation: MDL or MDA 2 AMP/ 250 Volt SLO-BLO size 1/4" X 1 1/4" | |
| B+ FUSE | MDA 1/2A Ceramic SLO-BLO size 1/4" x 1 1/4" |
| Dimensions | 15" deep x 13" wide x 8.75" tall |
| Shipping weight each | 45 pounds |
