Revox ist 2003 stolze 75 Jahre alt geworden. Alleine das ist schon Grund zum Feiern. Aber Revox hat auch ein besonderes Angebot für Fans, man kann gewissermaßen Mitglied in einem sehr exklusiven Club werden.
>> Mehr erfahren>> Alle anzeigenEs gibt Lautsprecher und dann gibt es noch die LS3/5A. Sie spaltet sowohl ihre Hörer, als auch die, die sie gar nicht kennen. Warum das so ist? Nun, dafür muss man sich vor allem anschauen und natürlich hören, was sie kann und nicht, was sie nicht kann.
>> Mehr erfahren>> Alle anzeigenKategorie: Verstärker Endstufen
Ausstattungsliste: Crestron AMP-2210HT
Technische Daten | |
Typical of 2 mono amplifier channels: | |
Input Signal Type | Balanced or unbalanced analog line-level |
Output Signal Types | 4/8 Ohm or 70 Volt |
Output Power | 120 Watts at 8 Ohms; |
210 Watts at 4 Ohms; | |
420 Watts at 8 Ohms bridged; | |
210 Watts at 70 Volts | |
Damping Factor | >100 |
Protection | Over Current, Over/Under Voltage, Over Temperature, DC Offset |
Frequency Response | 20Hz to 20kHz ±0.5 dB at 4/8 Ohms; |
80Hz to 20kHz +0/-3 dB at 70 Volts | |
THD | 0.05% @ 1kHz, full rated power at 4/8 Ohms, 8 Ohms Bridged, or 70/100 Volts; |
0.1% @ 20Hz to 20kHz, 120W at 8 Ohms; | |
0.2% @ 20Hz to 20kHz, 210W at 4 Ohms; | |
0.1% @ 20Hz to 20kHz, 420W at 8 Ohms Bridged; | |
0.1% @ 80Hz to 20kHz, 210W at 70 Volts | |
S/N Ratio | >103 dB, A-weighted |
Crosstalk | >70 dB @ 1kHz |
Gain | 23 dB with INPUT LEVEL control set at 12 o |
Input Sensitivity | 2.22 Vrms for rated output power with INPUT LEVEL control set at 12 o |
Input Detection Threshold | 40 mV RMS @ 1 kHz |
Input Level Adjustment | ±10 dB from nominal |
Connectors | |
G | 6-32 screw, chassis ground lug |
INPUT CH 1 – 2 | (2) 3-pin 3.5mm detachable terminal blocks; |
Balanced/unbalanced line-level audio inputs; | |
Input Level: 5.3 Vrms maximum with INPUT LEVEL control set at minimum position; | |
Input Impedance: 24k Ohms balanced, 12k Ohms unbalanced | |
SPEAKER OUTPUT CH 1 – 2 | (2) 4-pin 7.62mm 15A detachable terminal blocks; |
4Ω/8Ω and 70V power amplifier outputs; | |
Wire Size: Terminals accept up to 14 AWG | |
REMOTE | (1) 6-pin 3.5mm detachable terminal block; |
Provides (2) remote control inputs; enables independent power control of each channel via local jumpers or remote contact closures; | |
inputs may be safely paralleled for global control | |
FUSE T6.3AH 250V | Main fuse holder; |
5x20 mm, 250V, 6.3AH, time-lag, high-rupture rated | |
100-240V~50/60Hz | (1) IEC C14 male chassis plugs, main power input; Mates with removable power cord (included) |
Controls & Indicators | |
PWR | (1) dual-color LED, green indicates ACTIVE state, yellow indicates STANDBY state |
INPUT 1 – 2, SIGNAL | (2) green LEDs, indicate signal presence on each corresponding channel |
OUTPUT 1 – 2, CLIP | (2) amber LEDs, indicate a clipping condition on each corresponding channel |
OUTPUT 1 – 2, FAULT | (2) red LEDs; indicate over-temperature, over-current, over or under power supply voltage, or DC offset condition on each corresponding channel |
INPUT CH 1 – 2 LEVEL (rear) | (2) Rotary input boost/attenuate adjustments w/center detent at nominal |
SPEAKER OUTPUT CH 1 – 2, 70V / 4/8Ω (rear) | (2) 2-position slide switches, select the output configuration for each corresponding channel |
ON/REMOTE/OFF (rear) | (1) 3-position slide switch; selects between all channels powered on, all channels powered off, or remote control of each individual channel |
Power Requirements | |
Main Power | 100-240 Volts AC, 50/60 Hz |
Power Consumption | 62 Watts @ 8 Ohms, all channels driven at 1/8th output power; |
88 Watts @ 4 Ohms, all channels driven at 1/8th output power; | |
89 Watts @ 70V, all channels driven at 1/8th output power; | |
26 Watts, all channels idle; | |
<1 Watt in standby | |
Environmental | |
Temperature | 41° to 104°F (5° to 40°C) |
Humidity | 10% to 90% RH (non-condensing) |
Heat Dissipation | 110 BTU/Hr @ 8 Ohms, all channels driven at 1/8th output power; |
121 BTU/Hr @ 4 Ohms, all channels driven at 1/8th output power; | |
125 BTU/Hr @ 70V, all channels driven at 1/8th output power; | |
89 BTU/Hr, all channels idle; | |
<3.4 BTU/Hr in standby | |
Enclosure | |
Chassis | Metal with black finish, vented top and sides, convection cooled |
Front Panel | Metal, black finish with polycarbonate label overlay |
Mounting | Freestanding or 1U 19-inch rack-mountable (adhesive feet and rack ears included) |
Dimensions | |
Height | 1.70 in (44 mm) |
Width | 17.28 in (439 mm); |
19.0 in (483 mm) with rack ears | |
Depth | 14.59 in (371 mm) |
Weight | 15.6 lb (7.1 kg) |