
Für die Älteren unter uns gehören diese Lautsprecher zu den ersten jugendlichen Audiowunschträumen, wie zum Beispiel das Klipschorn oder die Electro Voice Sentry III. Für alle anderen könnte dieser besondere Lautsprecher eine echte Überraschung werden.
>> Mehr erfahren>> Alle anzeigen
Von Audio System gibt es eine Vielzahl an Nachrüstlautsprechern für Audi. Wir schaffen den Überblick und testen das RFIT Set für den A6 C8.
>> Mehr erfahren>> Alle anzeigenKategorie: Profi- / Musiker-Equipment
Ausstattungsliste: Manley TNT
Specification | |
Type | 2-CH MICROPHONE PREAMPLIFIER |
TUBE CHANNEL (left channel) | |
Vacuum Tubes | 1 x 12AT7EH + 1 x NOS 6414 |
Gain Range | +10 dB to +80 dB (20 to 70dB in 5 dB steps) |
Mic Input Impedance | 600, 2400, 10,000 Ohms Instrument |
Input Impedance | 300K,1Meg, 3 Meg Ohms |
Frequency Response | (-1 dB) 10 Hz to 30 kHz; (-3dB) 5 Hz to 45 kHz |
THD & NOISE (1 kHz @ 20 dB gain) | 0.035% typical (-68 dB) |
Noise Floor | -60 dB typical referenced to +4dBm |
EIN | -120 dB |
Signal to Noise @ 70 dB Gain | 95dB (TRIM has major effect) |
Maximum Output for 1% THD via BALANCED +4 XLR | 31 dBu |
COOL CHANNEL (right / solid state channel) | |
Gain Range | +10 dB to +80 dB (20 to 70dB in 5 dB steps) |
Mic Input Impedance | 300, 600, 2000, 2 Meg Ohms |
Instrument Input Impedance | 100K, 300K,1Meg, 3 Meg, 10 Meg Ohms |
Frequency Response | (-1 dB) 15 Hz to 30 kHz; (-3dB) 5 Hz to 50 kHz |
THD & NOISE (1 kHz @ 20 dB gain) | 0.01% typical (-80 dB) (no distortion products measurable, noise dominates measurement) |
Noise Floor | -66 dB typical referenced to +4dBm |
EIN | -126 dB |
Signal to Noise @ 70 dB Gain | 85dB (TRIM has little effect) |
Maximum Output for 1% THD | via BALANCED +4 XLR: 30 dBu |
via UNBALANCED +4 output: 24 dBu | |
via UNBALANCED -10 output: 16 dBu | |
Distortion @ 1K using 60 / 70s switch | 1.5% typical with LED onset (+4 dBu out) |
3% typical with LED fully lit (+7 dBu out) | |
GENERAL | |
Power consumption | 30 watts |
Operating mains voltage | Units power transformers are wired for original destination countrys mains voltage: 100V, 120V, or 220-240VAC as indicated on the serial number badge. |
Power transformer must be rewired on the pcb in order to change mains operating voltage. Fuse must be changed to appropriate value. | |
Mains Voltage Frequency | 50~ 60Hz |
Fuse Values S/N up to MTNT142 | @ 100 - 120V operation: 1A; @ 220 - 240V operation: 500mA |
Fuse Values S/N after MTNT142 | @ 100 - 120V operation: 500mA; @ 220 - 240V operation: 250mA |
Fuse Size | 1/4" x 1 1/4" MDL or MDA SLO-BLO (time delay) type |
Dimensions | 19" x 1 3/4" x 10" (occupies 1u) |
Unit Weight | 11 lbs. |