574_0_3
Anzeige
Topthema: Spüren Sie jeden Film – Kinosofas für das ultimative 4D-Erlebnis
Maximaler Komfort meets Cinema-Qualität für zu Hause
Sofanellas hochwertige Kinosofas vereinen 4D-Technologie mit Premium-Komfort. Keine überfüllten Kinosäle mehr: Genießen Sie Blockbuster in Ihrem privaten Luxus-Kino.
>> Mehr erfahren>> Alle anzeigen
588_24248_2
Topthema: Audio System M-700.1MD, Audio System M-750.1MD 24V
Kleinstgeräte
Mit M-700.1MD und M-750.1MD 24V präsentiert Audio System Bassverstärker mit bisher nicht dagewesener Leistung auf kleinstem Raum.
>> Mehr erfahren>> Alle anzeigenKategorie: Profi- / Musiker-Equipment
Ausstattungsliste: Dynacord IPX20:4
Ausstattung & technische Daten
| Specification | |
| Type | 4 x 5000 w multi‑channel installation dsp class‑d amplifier |
| OUTPUT POWER | |
| Low-Z mode: Load Impedance 2 Ω | Normal Mode, all channels driven: 5200 W |
| Parallel: 10000 W | |
| Direct Drive Mode: Nominal Voltage: 70 V | |
| Maximum Output Power: 3550 W | |
| Low-Z mode: Load Impedance 2.7 Ω | Normal Mode, all channels driven: 6000 W |
| Parallel: 8000 W | |
| Direct Drive Mode: Nominal Voltage: 100 V | |
| Maximum Output Power: 5000 W | |
| Low-Z mode: Load Impedance 4 Ω | Normal Mode, all channels driven: 5000 W |
| Parallel: 5000 W | |
| Direct Drive Mode: Nominal Voltage: 140 V | |
| Maximum Output Power: 5000 W | |
| Low-Z mode: Load Impedance 8 Ω | Normal Mode, all channels driven: 2500 W |
| Number of amplifier channels | 4 |
| Maximum Output Voltage | 210 V peak |
| Maximum Output Current | 84 A peak |
| AMPLIFIER | |
| Voltage Gain ref.1 kHz | 32.0 dB, adjustable 24-40 dB |
| Input Sensitivity ref. to Max. Output Voltage | 13.7 dBu (3.73 V), adjustable 5.7-21.7 dBu |
| THD 3 dB below Max., AES17, 1 kHz | < 0.05 % |
| IMD-SMPTE, 60 Hz, 7 kHz | < 0.15 % |
| DIM100, 3.15 kHz, 15 kHz | < 0.15 % |
| Crosstalk ref. 1 kHz, 12 dB below Max., 8 Ω | < -80 dB |
| Frequency Response ref. 1 kHz, analog in to speaker out | 20 Hz to 20 kHz (ą0.5 dB) |
| Damping Factor, 20 Hz to 200 Hz, 8 Ω | > 400 |
| Output Stage Topology | Class D, fixed frequency |
| Signal to Noise Ratio | A-weighted, analog input 115 dB |
| A-weighted, digital input 118 dB | |
| Output Noise | A-weighted, analog input < -70 dBu |
| A-weighted, digital input < -73 dBu | |
| DIGITAL SIGNAL PROCESSING | |
| Sampling rate | 48 kHz/96 kHz, OMNEO/Dante synchronized |
| Signal Delay/Latency | Analog in to Speaker Out, 48 kHz/96 kHz 0.70 ms/0.53 ms |
| AES3 in to Speaker Out, 48 kHz/96 kHz 1.00 ms/0.66 ms | |
| Dante Network Latency | typ. 1.00 ms |
| Signal Processing | 32/40 bit, floating point |
| User EQ | 12 filters per channel, selectable as PEQ, Lo-Shelv, Hi-Shelv, Lo-ShelvQ, Hi-ShelvQ, Hi-Pass, Lo-Pass & Notch; 2 filters of them with additional asymmetric filter type |
| User Delay | 0 to 2000 ms per channel (units: µs, ms, s,cm, m, inches, feet) |
| Array EQ | 5 filters per channel, selectable as PEQ, Lo-Shelv, Hi-Shelv, Lo-ShelvQ, Hi-ShelvQ, Hi-Pass, Lo-Pass, & All-Pass |
| Array Delay | 0 to 500 ms per channel (units: µs, ms, s, cm,m, inches, feet) |
| Speaker EQ | 10 filters per channel, selectable as PEQ, Lo-Shelv, Hi-Shelv, Hi-Pass, Lo-Pass, & All-Pass |
| Speaker X-Over | Hi-Pass & Lo-Pass per channel, 6/12/18/24/30/36/42/48 dB Bessel/Butterworth,12/24/48 dB Linkwitz-Riley; AlignmentDelay, 0 to 20 ms per channel |
| Speaker FIR | up to 1025 taps, Linear Phase Filter, Linear Phase Brickwall X-Over |
| Speaker Limiters | Peak Anticipation Limiter & RMS/TEMP Limiter per channel |
| Other functions | Source Selection & Mix, Level, Mute, Polarity, Sine & Noise Generator, Level Meters, Impedance Measurement, & Load Monitoring |
| Memory | DSP Presets 1 Factory + 20 User |
| Speaker-Pool Presets 30 speaker settings | |
| Source Supervision & Fallback AES3 Lock & OMNEO/Dante network supervision, switchover to alternative Source Selection | |
| CONNECTIVITY Analog Audio Input/Thru | |
| Type | 4 x 3-pin XLR female/male |
| Maximum Input Level | +24 dBu |
| Input Impedance, active balanced | 20 kΩ |
| Reference level equal to digital input | +21 dBu for 0 dBFS |
| CONNECTIVITY Digital Audio Input/Thru | |
| Type | 2 x 3-pin XLR (alternative use of Analog In/Thru) |
| Format | AES3 (AES/EBU) |
| Input Sample Rates | 32 to 192 kHz, internal Sample-Rate-Converter |
| Thru Connector | active buffered, direct bypass if device is unpowered |
| CONNECTIVITY Network | |
| Type | 2 x Neutrik etherCON/RJ45, redundant PRIMARY/SECONDARY |
| Format | 1000base-T/100base-TX, integrated switch |
| Network Audio Inputs | 8 channels, 48/96 kHz, OMNEO/Dante format |
| Network Audio Outputs (Monitor) | 2 channels, 48/96 kHz, OMNEO/Dante format |
| Front side Service Port | 1 x USB Type A |
| Mains Input | 1 x Neutrik powerCON-HC |
| Speaker Output | 4 x NL4 |
| GENERAL User Interface | |
| Display | 320 x 240 pixel, 3.5" color TFT |
| Front panel indicators | Full color LED illuminated ring |
| Front panel operating elements | Rotary encoder, Capacitive Touch Screen |
| Rear panel indicators | 2 x LED (AES3 Input mode active, Amp-Find) |
| Rear panel operating elements | Mains switch |
| Power Requirements | 100 V to 240 V, 50 Hz to 60 Hz AC |
| GENERAL Power Consumption | |
| Rated Power Consumption | 2250 W |
| ⅛ Maximum Output Power at 4 Ω | 2850 W |
| Idle Mode (no input signal) | 110 W |
| Standby Mode | < 19 W |
| Power Supply Topology | Switching Mode Power Supply with digital controlled Power Factor Correction |
| Protections | Audio Limiters, High Temperature, DC, HF, Short Circuit, Back-EMF, Peak Current Limiters, In rush Current Limiters, Turn-on Delay, Mains Circuit Breaker Protection, Mains Over/Under voltage Protection |
| Cooling | Front-to-rear, temperature controlled fans, supervised |
| Ambient Temperature Limits | +5 °C to +40 °C (+40 °F to +105 °F) |
| IEC Protection Class | Class I (grounded) |
| Electromagnetical Environment | E1, E2, E3 |
| Color | Black |
| Dimensions (W x H x D), mm | 483 x 88.1 x 514.2 |
| Weight | 18.3 kg (40.4 lb) |
