462_22882_2
Topthema: Feurig
High-End-Standbox mit ESS AMT
Mit diesen Chassis wollte ich schon immer mal etwas bauen. Dass ich sie allerdings jemals zusammen in einer Box haben würde, hätte ich dann doch wieder nicht erwartet – dass das Ganze so gut werden würde, dann schon eher.
>> Mehr erfahren>> Alle anzeigen
390_22002_2
Topthema: Sound im Audi
Audio System RFIT Audi A6 C8 Evo2 – 20er System für Audi A6
Von Audio System gibt es eine Vielzahl an Nachrüstlautsprechern für Audi. Wir schaffen den Überblick und testen das RFIT Set für den A6 C8.
>> Mehr erfahren>> Alle anzeigenKategorie: Vollverstärker
Ausstattungsliste: Parasound HINT 6
Ausstattung & technische Daten
| Specification | |
| Power Output - Both channels driven | (0.9% THD, 20 Hz - 20 kHz) |
| 180 watts x 2 @ 8 Ω RMS | |
| 270 watts x 2 @ 4 Ω RMS | |
| Current Capacity | 45 amps peak per channel |
| Frequency Response | 10 Hz - 100 kHz, +0/-3 dB |
| 20 Hz - 20 kHz, +0/-0.5 dB | |
| Total Harmonic Distortion (THD) | < 0.01 %, average listening levels |
| < 0.05 %, 160 watts x 2 @ 8 Ω | |
| Interchannel Crosstalk | > 70 dB at 20 kHz |
| > 78 dB at 1 kHz | |
| Signal to Noise Ratio - IHF A-weighted | Line in: - 103 dB (input shorted) |
| Digital in: - 106 dB | |
| Amplifier Damping Factor | > 800 at 20 Hz |
| Preamplifier Stage Input Sensitivity | 300 mV in for 1 V at Preamp Output jacks |
| Total Preamp Stage Gain: 10 dB | |
| Max Output Unbalanced: 7 V | |
| Max Output Balanced: 9 V | |
| Power Amplifier Stage Sensitivity | 1 V at Bypass/Amp In for 28 V at Speaker Out |
| Total Amp Stage Gain: 28 dB | |
| Phono Stage Sensitivity / Input Impedance | MM: 41 dB / 47 k Ω |
| MC: 54 dB / 47 k Ω or 100 Ω | |
| High & Low Pass Crossover Slope | 12 dB per octave |
| Supported DAC Sampling Rates | USB: up to 384 kHz / 32-bit PCM |
| DSD Native: DSD 64, DSD 128, DSD 256 | |
| DSD over PCM (DoP) at 384 kHz | |
| Coax/Optical | up to 192 kHz / 24-bit PCM |
| Digital to Analog Converter | ESS Sabre32 Reference ES9018K2M |
| 384 kHz / 32-bit | |
| USB 2.0 Controller | Savitech SA9227, 384 kHz / 32-bit |
| Headphone Amplifier | Texas Instruments TPA6120A |
| Output Impedance 10 ohms | |
| XLR Pin Identification | 1 = Ground (Shield) |
| 2 = Positive | |
| 3 = Negative (Return) | |
| Input Impedance | Unbalanced: 24 k Ω |
| Balanced: 100 k Ω per leg | |
| Preamplifer Output Impedance | Unbalanced: 100 Ω |
| Balanced: 470 Ω per leg | |
| Power Requirement | Standby: 0.5 watts |
| Idling power: 70 watts | |
| Maximum: 750 watts | |
| 110-125 VAC 60 Hz or 220-250 VAC 50 Hz | |
| AC mains voltage is set on rear panel | |
| Dimensions | Width: 17-1/4" (437 mm) |
| Depth: 16-1/4" (413 mm) | |
| Depth, with cables 17-1/4" (437 mm) | |
| Height, with feet: 5-7/8" (150 mm) | |
| Height, without feet: 5-1/4" (133 mm), 3U | |
| Net Weight | 33 lb. (15 kg) |
